MMaterialsgateNEWS vom 01.11.2016

Verwandte MaterialsgateCARDS

Researchers surprised at the unexpected hardness of gallium nitride

A Lehigh University team discovers that the widely used semiconducting material is almost as wear-resistant as diamonds

Gallium nitride (GaN) has emerged as one of the most important and widely used semiconducting materials. Its optoelectronic and mechanical properties make it ideal for a variety of applications, including light-emitting diodes (LEDs), high-temperature transistors, sensors and biocompatible electronic implants in humans.

In 2014, three Japanese scientists won the Nobel Prize in physics for discovering GaN's critical role in generating blue LED light, which is required, in combination with red and green light, to produce white LED light sources.

Now, four Lehigh engineers have reported a previously unknown property for GaN: Its wear resistance approaches that of diamonds and promises to open up applications in touch screens, space vehicles and radio-frequency microelectromechanical systems (RF MEMS), all of which require high-speed, high-vibration technology.

The researchers reported their findings in August in Applied Physics Letters (APL) in an article titled "Ultralow wear of gallium nitride." The article's authors are Guosong Zeng, a Ph.D. candidate in mechanical engineering; Nelson Tansu, Daniel E. '39 and Patricia M. Smith Endowed Chair Professor in the Electrical and Computer Engineering department, and Director of the Center for Photonics and Nanoelectronics (CPN); Brandon A. Krick, assistant professor of mechanical engineering and mechanics; and Chee-Keong Tan '16 Ph.D., now assistant professor of electrical and computer engineering at Clarkson University.

GaN's electronic and optical properties have been studied extensively for several decades, said Zeng, the lead author of the APL article, but virtually no studies have been done of its tribological properties, that is, its resistance to the mechanical wear imposed by reciprocated sliding.

"Our group is the first to investigate the wear performance of GaN," said Zeng. "We have found that its wear rate approaches that of diamonds, the hardest material known."

Wear rate is expressed in negative cubic millimeters of Newton meters (Nm). The rate for chalk, which has virtually no wear resistance, is on the order of 10 2 mm3/Nm, while that of diamonds is between 10-9 and 10-10, making diamonds eight orders of magnitude more wear resistant than chalk. The rate for GaN ranges from 10¬-7 to 10-9, approaching the wear resistance of diamonds and three to five orders of magnitude more wear resistant than silicon (10-4).

The Lehigh researchers measured the wear rate and friction coefficients of GaN using a custom microtribometer to perform dry sliding wear experiments. They were surprised by the results.

"When performing wear measurements of unknown materials," they wrote in APL, "we typically slide for 1,000 cycles, then measure the wear scars; [these] experiments had to be increased to 30,000 reciprocating cycles to be measurable with our optical profilometer.

"The large range in wear rates (about two orders of magnitude)...can provide insight into the wear mechanisms of GaN."

That range in wear resistance, the researchers said, is caused by several factors, including environment, crystallographic direction and, especially, humidity.

"The first time we observed the ultralow wear rate of GaN was in winter," said Zeng. "These results could not be replicated in summer, when the material's wear rate increased by two orders of magnitude."

To determine how the higher summer humidity was affecting GaN's wear performance, the researchers put their tribometer in a glove box that can be backfilled with either nitrogen or humid air.

"We observed that as we increased the humidity inside the glove box, we also increased the wear rate of GaN," said Zeng.

Zeng gave a presentation about the Lehigh project in October at the International Workshop on Nitride Semiconductors (IWN 2016) in Orlando, Florida. The session at which he spoke was titled "Wear of Nitride Materials and Properties of GaN-based structures." Zeng was one of seven presenters at the session and the only one to discuss the wear properties of GaN and other III-Nitride materials.

Tansu, who has studied GaN for more than a decade, and Krick, a tribology expert, became curious about GaN's wear performance several years ago when they discussed their research projects after a Lehigh faculty meeting.

"Nelson asked me if anyone had ever investigated the friction and wear properties of gallium nitride," said Krick, "and I said I didn't know. We checked later and found a wide-open field."

Tansu said the group's discovery of GaN's hardness and wear performance could have a dramatic effect on the electronic and digital device industries. In a device such as a smartphone, he said, the electronic components are housed underneath a protective coating of glass or sapphire. This poses potential compatibility problems which could be avoided by using GaN.

"The wear resistance of GaN," said Tansu, "gives us the opportunity to replace the multiple layers in a typical semiconductor device with one layer made of a material that has excellent optical and electrical properties and is wear-resistant as well.

"Using GaN, you can build an entire device in a platform without multiple layers of technologies. You can integrate electronics, light sensors and light emitters and still have a mechanically robust device. This will open up a new paradigm for designing devices. And because GaN can be made very thin and still strong, it will accelerate the move to flexible electronics."

In addition to its unexpectedly good wear performance, said Zeng, GaN also has a favorable radiation hardness, which is an important property for the solar cells that power space vehicles. In outer space, these solar cells encounter large quantities of very fine cosmic dust, along with x-rays and gamma rays, and thus require a wear-resistant coating, which in turn needs to be compatible with the cell's electronic circuitry. GaN provides the necessary hardness without introducing compatibility issues with the circuitry.

The Lehigh group has begun collaborating with Bruce E. Koel, a surface chemistry expert and professor of chemical and biological engineering at Princeton University, to gain a better understanding of the interaction of GaN and water under contact. Koel was formerly a chemistry professor and vice president for research and graduate studies at Lehigh.

To determine the evolution of wear with GaN, the group has subjected GaN to stresses by running slide tests in which the slide distance and the corresponding number of cycles are varied. The group then uses an x-ray photoelectron spectrometer (XPS), which can identify the elemental composition of the first 12 nanometers of a surface, to scan the unworn surface of the GaN, the scar created by the slide machine, and the wear particles deposited by the slide machine on either side of the scar.

The group plans next to use aberration-corrected transmission electron microscopy to examine the lattice of atoms beneath the scar. Meanwhile, they will simulate a test in which the lattice is strained with water in order to observe the variations caused by deforming energy.

"This is a very new experiment," said Zeng. "It will enable us to see dynamic surface chemistry by watching the chemical reaction that results when you apply shear, tensile or compressive pressure to the surface of GaN."

Source: Lehigh University – 28.10.2016.

Recherchiert und dokumentiert von:

Dr.-Ing. Christoph Konetschny, Inhaber und Gründer von Materialsgate
Büro für Material- und Technologieberatung
Die Recherche und Aufbereitung der in diesem Dokument genannten Daten erfolgte mit größter Sorgfalt.
Für die Richtigkeit, Gültigkeit, Verfügbarkeit und Anwendbarkeit der genannten Daten übernehmen wir zu keinem Zeitpunkt die Haftung.
Bitte diskutieren Sie die Verwendung und Eignung für Ihren konkreten Anwendungsfall mit den Experten der genannten Institution.

Sie wünschen Material- und Technologierecherchen zu diesem Thema?

Materialsgate steht für hochwertige Werkstoffberatung und innovative Materialrecherchen.
Nutzen Sie unseren Beratungsservice

MMehr zu diesem Thema

Researchers combine diamond and cubic boron nitride with a novel alloying process for a superhard material

Diamonds are forever, except when they oxidize while cutting through iron, cobalt, nickel, chromium, or vanadium at high temperatures. Conversely, cubic boron nitride possesses superior chemical inertness but only about half of the hardness of diamonds. In an attempt to create a superhard material better suited for a wide variety of materials on an industrial scale, researchers at Sichuan University in Chengdu, China, have created an alloy composed of diamonds and cubic boron nitride (cBN) that boasts the benefits of both. "Diamond and cubic boron nitride could readily form alloys that can potentially fill the performance gap because of their affinity in structure lattices and covalent... mehr mehr lesen

Researchers from the Technological Institute for Superhard and Novel Carbon Materials in Troitsk, MIPT, MISiS, and MSU have developed a new method for the synthesis of an ultrahard material that exceeds diamond in hardness.

An article recently published in the journal Carbon describes in detail a method that allows for the synthesis of ultrahard fullerite, a polymer composed of fullerenes, or spherical molecules made of carbon atoms. In their work, the scientists note that diamond hasn’t been the hardest material for some time now. Natural diamonds have a hardness of nearly 150 GPa, but ultrahard fullerite has surpassed diamond to become first on the list of hardest materials with values that range from 150 to 300 GPa. All materials that are harder than diamond are called ultra hard materials. Materials softer than diamond but harder than boron nitride are termedsuperhard. Boron nitride, with its cubic... mehr mehr lesen

An international team led by Artem R. Oganov, PhD, a professor of theoretical crystallography in the Department of Geosciences at Stony Brook University, has established the structure of a new form of carbon.

The results of their work, “Understanding the Nature of Superhard Graphite,” were published June 26 in Scientific Reports, a new journal of the Nature Publishing Group. Dr. Oganov and his team used a novel computational method to demonstrate that the properties of what had previously been thought to be only a hypothetical structure of a superhard form of carbon called “M-carbon” – constructed by Oganov in 2006 – matched perfectly the experimental data on “superhard graphite.” “Most of the known forms of carbon have a colorful story of their discovery and a multitude of real or potential revolutionary applications,” said Oganov. “Think of diamond, a record-breaking... mehr mehr lesen


Partner der Woche

Suche in MaterialsgateNEWS

Bücher und Produkte