MMaterialNews 2012/06/12

Energy: Photovoltaic Cells Tap Underwater Solar Energy

Scientists at the U.S. Naval Research Laboratory, Electronics Science and Technology Division, dive into underwater photovoltaic research to develop high bandgap solar cells capable of producing sufficient power to operate electronic sensor systems at depths of 9 meters.
Underwater autonomous systems and sensor platforms are severely limited by the lack of long endurance power sources. To date, these systems must rely on on-shore power, batteries or solar power supplied by an above water platform. Attempts to use photovoltaics have had limited success, primarily due to the lack of penetrating sunlight and the use of solar cells optimized more towards the unimpeded terrestrial solar spectrum.

"The use of autonomous systems to provide situational awareness and long-term environment monitoring underwater is increasing," said Phillip Jenkins, head, NRL Imagers and Detectors Section. "Although water absorbs sunlight, the technical challenge is to develop a solar cell that can efficiently convert these underwater photons to electricity."

Even though the absolute intensity of solar radiation is lower underwater, the spectral content is narrow and thus lends itself to high conversion efficiency if the solar cell is well matched to the wavelength range. Previous attempts to operate solar cells underwater have focused on crystalline silicon solar cells and more recently, amorphous silicon cells.

High-quality gallium indium phosphide (GaInP) cells are well suited for underwater operation. GaInP cells have high quantum efficiency in wavelengths between 400 and 700 nanometers (visible light) and intrinsically low dark current, which is critical for high efficiency in lowlight conditions.

The filtered spectrum of the sun underwater is biased toward the blue/green portion of the spectrum and thus higher bandgap cells such as GaInP perform much better than conventional silicon cells, states Jenkins.

Preliminary results at a maximum depth of 9.1 meters reveal output to be 7 watts per square meter of solar cells, sufficient to demonstrate there is useful solar power to be harvested at depths commonly found in nearshore littoral zones.

Source: U.S. Naval Research Laboratory – 07-06.2012.

Investigated and edited by:

Dr.-Ing. Christoph Konetschny, Materials Consultant, Owner of Materialsgate
The investigation and editing of this document was performed with best care and attention. For the accuracy, validity, availability and applicability of the given information, we take no liability. Please discuss the suitability concerning your specific application with the experts of the named company or organization.

You want additional material or technology investigations concerning this subject?

Materialsgate is leading in material consulting and material investigation.
Feel free to use our established consulting services

MMore on this topic

New inexpensive, environmentally friendly solar cell shines with potential
The limitations of conventional and current solar cells include high production cost, low operating efficiency and durability, and many cells rely on toxic and scarce materials. Northwestern University researchers have developed a new solar cell that, in principle, will minimize all of these solar energy technology limitations. In particular, the device is the first to solve the problem of the Grätzel cell, a promising low-cost and environmentally friendly solar cell with a significant disadvantage:... more
Liquid solar cells are cheaper, more flexible than existing solar options
Scientists at USC have developed a potential pathway to cheap, stable solar cells made from nanocrystals so small they can exist as a liquid ink and be painted or printed onto clear surfaces. The solar nanocrystals are about four nanometers in size — meaning you could fit more than 250,000,000,000 on the head of a pin — and float them in a liquid solution, so "like you print a newspaper, you can print solar cells," said Richard L. Brutchey, assistant professor of chemistry at the... more
The coolest new nanomaterial of the 21st century could boost the efficiency of the next generation of solar panels, a team of Michigan Technological University materials scientists has discovered.
Graphene, a two-dimensional honeycomb of carbon atoms, is a rising star in the materials community for its radical properties. One of those properties is electrical conductivity, which could make it a key ingredient in the next generation of photovoltaic cells, says Yun Hang Hu, a professor of materials science and engineering. Dye-sensitized solar cells don’t rely on rare or expensive materials, so they could be more cost-effective than cells based on silicon and thin-film technologies. But... more
To produce the maximum amount of energy, solar cells are designed to absorb as much light from the Sun as possible. Now researchers from the University of California, Berkeley, have suggested – and demonstrated – a counterintuitive concept: solar cells should be designed to be more like LEDs, able to emit light as well as absorb it.
The Berkeley team will present its findings at the Conference on Lasers and Electro Optics (CLEO: 2012), to be held May 6-11 in San Jose, Calif. "What we demonstrated is that the better a solar cell is at emitting photons, the higher its voltage and the greater the efficiency it can produce," says Eli Yablonovitch, principal researcher and UC Berkeley professor of electrical engineering. Since 1961, scientists have known that, under ideal conditions, there is a limit to the amount of... more
RSS
facebook
xing
twitter
linkedin

MaterialCards Weekly

Your personal and free material reminder - weekly by email

Service:
Material Charac­teri­za­tion
and Testing

You Need Advanced and Efficient Methods of Material Charac­teri­za­tion and Testing to Optimize Your Products?
Fracture Mechanics
Characterization of Coatings
Characterization of Diffusion Profiles
Thermography
Characterization of Nano-Coatings
Characterization of Joining Technologies
Characterization of Electrical and Thermal Properties
Characterization of Catalysts
Metallography
Characterization of Barrier Properties
Corrosion Tests
Characterization of Materials for Medical Applications
Microstructure Analysis
Automotive Testing
Failure Analysis of Composites
Failure Analysis of Products
Testing of Plastics and Polymers
Characterization of Composites
Ceramography
Element Mapping
Fracture Mechanics
Characterization of Coatings
Characterization of Diffusion Profiles
Thermography
Characterization of Nano-Coatings
Characterization of Joining Technologies
Characterization of Electrical and Thermal Properties
Characterization of Catalysts
Metallography
Characterization of Barrier Properties
Corrosion Tests
Characterization of Materials for Medical Applications
Microstructure Analysis
Automotive Testing
Failure Analysis of Composites
Failure Analysis of Products
Testing of Plastics and Polymers
Characterization of Composites
Ceramography
Element Mapping
Contact us – We will forward your request to one of our qualified co­operation partners in this field. All of them operate certified la­bo­ra­to­ries with modern and the most diverse equipment.

Recommended Books

Duncan W. Bruce, Richard I. Walton, Dermot O'Hare
John Wiley & Sons
Gawdat Bahgat
John Wiley & Sons